How to Get a Water Heater Permit in Hillsboro, OR (2026 Guide)

Everything you need to know about water heater permits in Hillsboro, OR, local requirements, fees, timelines, and how to apply.

By Joey, Founder · Last updated June 6, 2026 · How we research →

$25 – $500 Permit Fees
3 business days Approval Time
4 Local Rules

Check your specific water heater project

Get an instant, personalized answer for your exact project details in Hillsboro.

Free Permit Lookup →

Do You Need a Water Heater Permit in Hillsboro?

Based on Hillsboro's local building codes, you'll need a permit when:

Required·Rule 1

Same-for-same water heater replacement requires a plumbing permit. The new unit must meet current code including T&P valve (IRC P2803), discharge pipe (P2804.6.1), drain pan where required (P2801.6), and expansion tank if the home has a closed system (P2903.4). California, Washington, and most Oregon counties require seismic strapping, two straps minimum (upper third and lower third of the tank).

Source2021 Oregon Residential Specialty Code (based on 2021 IRC)
Required·Rule 2

Converting from a tank to a tankless gas water heater requires plumbing AND gas permits. Tankless units demand 150,000-199,000 BTU/hr at full capacity, about 4-5x a tank unit's demand. Existing gas lines are typically undersized and must be upgraded. New direct-vent or power-vent systems are required; existing B-vent cannot be reused.

Source2021 Oregon Residential Specialty Code (based on 2021 IRC)
Required·Rule 3

Installing a heat pump water heater requires plumbing AND electrical permits. HPWHs need a dedicated 240V/30A circuit, sufficient air volume (450-700 cubic feet minimum per manufacturer specs), and condensate drainage. Note: the federal 25C tax credit for HPWHs expired December 31, 2025, state and utility rebates may still apply.

Source2021 Oregon Residential Specialty Code (based on 2021 IRC)
Required·Rule 4

Relocating a water heater to a new location requires a full permit stack: plumbing (new water connections), gas (if gas-fired, new piping and venting), and electrical (for electric or heat pump units). This is significantly more complex than a same-location replacement and typically costs $1,500-$3,500 in additional plumber labor.

Source2021 Oregon Residential Specialty Code (based on 2021 IRC)

Permit Fees in Hillsboro

Based on local Hillsboro permit data, fees for water heater projects typically range:

$25 – $500 Hillsboro Permit Fee Range

Here's how fees break down by project scope nationally:

Project ScopeTypical Permit Fee
Standard tank replacement permit$25 – $150
Tankless conversion permit (plumbing + gas)$100 – $500
Heat pump water heater permit (plumbing + electrical)$100 – $400
Licensed plumber labor, same-for-same replacement$150 – $450
Tank water heater unit (40-50 gallon gas)$500 – $1,500
Tankless gas water heater unit$1,000 – $2,500
Heat pump water heater unit$1,500 – $3,500
Tank same-for-same total installed$900 – $1,800
Tankless conversion total installed$2,000 – $4,500+
Heat pump total installed (add electrical work if needed)$2,500 – $9,500
Expansion tank (if required as add-on)$90 – $350 installed
Seismic strap kit (CA/WA/OR)$10 – $30

Fees are typically calculated based on estimated project value. Contact Development Services & Permitting Center for exact amounts.

How Long Does It Take?

In Hillsboro, typical approval time for water heater permits is 3 business days.

More complex projects requiring structural review or variances may take longer. Simple projects may qualify for expedited or over-the-counter review in some cases.

How to Apply for a Water Heater Permit in Hillsboro

  1. 1 Check requirements: Use our free lookup tool or contact Development Services & Permitting Center to confirm your project needs a permit.
  2. 2 Gather documents: Prepare your application, site plan, construction drawings, and any other required documents.
  3. 3 Submit online: Hillsboro accepts applications online at Development Services & Permitting Center.
  4. 4 Pay fees: Pay the applicable permit fees ($25 – $500).
  5. 5 Wait for approval: Your application will be reviewed by Hillsboro plan reviewers. Typical turnaround is 3 business days.
  6. 6 Begin work: Once approved, post your permit visibly at the job site before starting work.
  7. 7 Schedule inspections: Call Development Services & Permitting Center at (503) 681-6153 to schedule required inspections at each phase of the project.

Hillsboro Building Department Contact

NameDevelopment Services & Permitting Center
Apply OnlineApply online
Address150 E Main Street, 4th Floor, Hillsboro, OR 97123
HoursMon-Fri 8am-5pm

Required Inspections in Hillsboro

Most water heater projects in Hillsboro require inspections at each construction stage:

Inspection·Stage 1

Rough-in (for relocations or major work), Supply connections correct size and material, dielectric unions for dissimilar metals, gas connections with proper valve and sediment trap, electrical connection and dedicated circuit, venting sized and routed correctly, combustion air provisions (gas), condensate drainage (HPWH).

WhenAfter water/gas/electrical connections are made but before the unit is enclosed or covered
Common FailuresMissing dielectric unions, improper gas shutoff valve location, inadequate combustion air, wrong vent type or size.
Inspection·Stage 2

Final inspection, T&P valve installed and discharge pipe compliant with P2804.6.1, drain pan in place where required, seismic strapping (CA/WA/OR) with two straps in correct positions, expansion tank if closed system, leak-free operation, proper venting, no clearances violations to combustibles (6 inches from B-vent, 1 inch from Type B), electrical or gas shutoffs accessible, combustion air for gas units, condensate drain for HPWH, equipment matches permit application.

WhenAfter installation is complete and unit is operational
Common FailuresT&P discharge pipe wrong size or configuration, missing drain pan, missing seismic straps, missing or wrong-size expansion tank, gas leaks at connections, venting not meeting clearances.

Schedule inspections with Development Services & Permitting Center at (503) 681-6153 at least 24–48 hours in advance.

Frequently Asked Questions

Whether you need a permit depends on the size and scope of your water heater project. In Hillsboro, some smaller projects are exempt while larger ones require a permit. Use our free lookup tool to check your specific situation.

Permit fees for water heater projects in Hillsboro typically range from $25 – $500. Fees are usually based on the estimated project value.

Typical approval time in Hillsboro is 3 business days. Complex projects requiring structural review may take longer.

In most cases, homeowners in Hillsboro can pull permits and perform work on their own primary residence as an owner-builder. You're still responsible for meeting all code requirements and passing inspections.

Working without a required permit in Hillsboro can result in fines, stop-work orders, required removal of completed work, and complications when selling your home.

Ready to check your water heater project in Hillsboro?

Use our free lookup tool to get a personalized answer based on your specific project details.

Free Permit Lookup →

Water Heater Permits in Nearby Cities

See water heater permit requirements in other Oregon cities:

See Detailed Water Heater Rules for Hillsboro

View all local rules, exemptions, and fee details on the permit page.

Water Heater Permit Rules →
Disclaimer: This guide provides general information about water heater permit requirements in Hillsboro, OR. Requirements can change. Always confirm with Development Services & Permitting Center before starting any project. PermitMint provides general guidance, not legal advice.