How to Get a Gas Line Permit in Hillsboro, OR (2026 Guide)

Everything you need to know about gas line permits in Hillsboro, OR, local requirements, fees, timelines, and how to apply.

By Joey, Founder · Last updated June 6, 2026 · How we research →

$50 – $400 Permit Fees
about 1 week Approval Time
4 Local Rules

Check your specific gas line project

Get an instant, personalized answer for your exact project details in Hillsboro.

Free Permit Lookup →

Do You Need a Gas Line Permit in Hillsboro?

Based on Hillsboro's local building codes, you'll need a permit when:

Required·Rule 1

Extending an existing gas line to serve a new appliance requires a gas permit. This includes running new branch lines for gas dryers, gas ranges, water heaters, fireplaces, outdoor fire pits, pool heaters, standby generators, and outdoor kitchens. A pressure test and inspection are required before concealing any piping.

Source2021 Oregon Residential Specialty Code (based on 2021 IRC)
Required·Rule 2

Outdoor gas lines for fire pits, grills (hard-piped), pool heaters, patio heaters, outdoor kitchens, and generators require a gas permit. Underground gas piping must be polyethylene (PE) per ASTM D2513, buried at least 12 inches deep, with transition to metallic pipe before any building entry.

Source2021 Oregon Residential Specialty Code (based on 2021 IRC)
Required·Rule 3

A new gas service line from the meter requires a gas/plumbing permit. The installation must meet IRC Chapter 24 (Fuel Gas) / IFGC Chapter 4 requirements, including pipe sizing, pressure testing at 3 psig minimum for 10 minutes, and inspection before the piping is covered or concealed. A licensed plumber is required in virtually all states.

Source2021 Oregon Residential Specialty Code (based on 2021 IRC)

These gas line projects are typically exempt in Hillsboro:

Exempt·Rule 1

Relighting a pilot light or adjusting an existing appliance's shutoff valve does not require a permit. Replacing a listed flexible appliance connector at an existing appliance is also typically exempt. Any work involving new piping, pipe extension, or appliance connections requires a permit.

Source2021 Oregon Residential Specialty Code (based on 2021 IRC)

Permit Fees in Hillsboro

Based on local Hillsboro permit data, fees for gas line projects typically range:

$50 – $400 Hillsboro Permit Fee Range

Here's how fees break down by project scope nationally:

Project ScopeTypical Permit Fee
Simple gas permit (single appliance connection)$50 – $150
Standard gas permit (new branch line or extension)$75 – $300
Major gas work (new trunk line, multiple appliances)$150 – $500+
Licensed plumber labor (gas work)$75 – $200/hour
Gas line extension for single appliance (total cost)$500 – $2,000
New trunk line serving multiple appliances$2,000 – $8,000+
Pressure test (if inspector requires witnessed test)Usually included in permit fee

Fees are typically calculated based on estimated project value. Contact Development Services & Permitting Center for exact amounts.

How Long Does It Take?

In Hillsboro, typical approval time for gas line permits is about 1 week.

More complex projects requiring structural review or variances may take longer. Simple projects may qualify for expedited or over-the-counter review in some cases.

How to Apply for a Gas Line Permit in Hillsboro

  1. 1 Check requirements: Use our free lookup tool or contact Development Services & Permitting Center to confirm your project needs a permit.
  2. 2 Gather documents: Prepare your application, site plan, construction drawings, and any other required documents.
  3. 3 Submit online: Hillsboro accepts applications online at Development Services & Permitting Center.
  4. 4 Pay fees: Pay the applicable permit fees ($50 – $400).
  5. 5 Wait for approval: Your application will be reviewed by Hillsboro plan reviewers. Typical turnaround is about 1 week.
  6. 6 Begin work: Once approved, post your permit visibly at the job site before starting work.
  7. 7 Schedule inspections: Call Development Services & Permitting Center at (503) 681-6153 to schedule required inspections at each phase of the project.

Hillsboro Building Department Contact

NameDevelopment Services & Permitting Center
Apply OnlineApply online
Address150 E Main Street, 4th Floor, Hillsboro, OR 97123
HoursMon-Fri 8am-5pm

Required Inspections in Hillsboro

Most gas line projects in Hillsboro require inspections at each construction stage:

Inspection·Stage 1

Rough-in / piping inspection, Pipe material is approved (black iron, CSST, or listed alternative), sizing matches the load calculation, support and hangers are correct, joints are accessible for the pressure test, shutoff valves are installed at required locations, sediment traps are present at water heaters and furnaces, CSST bonding is in place if applicable.

WhenAfter piping is installed, but before it's covered or concealed
Common FailuresUndersized pipe, prohibited materials (PVC), missing sediment traps, unsupported piping, CSST not bonded.
Inspection·Stage 2

Pressure test, Test pressure of at least 3 psig (1.5x max working pressure) held for minimum 10 minutes without any drop. Test medium is air, nitrogen, CO2, or inert gas. All joints exposed. Appliances isolated from the test. Inspector may witness in person or accept contractor certification depending on jurisdiction.

WhenAfter all new piping is complete, before covering or use
Common FailuresPressure drop indicating a leak (most common, usually at threaded joints), wrong test medium, joints covered before the test, inadequate test duration.
Inspection·Stage 3

Final inspection, Gas shutoff valves at appliances, flex connectors proper length and configuration, no leaks at connections (typically verified with soap bubble solution or electronic gas detector), appliance venting and combustion air (if covered under the same permit), system labeling if required.

WhenAfter appliances are connected and system is ready for service
Common FailuresLeaks at final connections, improper flex connector use (too long or running through walls), missing appliance shutoffs.

Schedule inspections with Development Services & Permitting Center at (503) 681-6153 at least 24–48 hours in advance.

Frequently Asked Questions

Whether you need a permit depends on the size and scope of your gas line project. In Hillsboro, some smaller projects are exempt while larger ones require a permit. Use our free lookup tool to check your specific situation.

Permit fees for gas line projects in Hillsboro typically range from $50 – $400. Fees are usually based on the estimated project value.

Typical approval time in Hillsboro is about 1 week. Complex projects requiring structural review may take longer.

In most cases, homeowners in Hillsboro can pull permits and perform work on their own primary residence as an owner-builder. You're still responsible for meeting all code requirements and passing inspections.

Working without a required permit in Hillsboro can result in fines, stop-work orders, required removal of completed work, and complications when selling your home.

Ready to check your gas line project in Hillsboro?

Use our free lookup tool to get a personalized answer based on your specific project details.

Free Permit Lookup →

Gas Line Permits in Nearby Cities

See gas line permit requirements in other Oregon cities:

See Detailed Gas Line Rules for Hillsboro

View all local rules, exemptions, and fee details on the permit page.

Gas Line Permit Rules →
Disclaimer: This guide provides general information about gas line permit requirements in Hillsboro, OR. Requirements can change. Always confirm with Development Services & Permitting Center before starting any project. PermitMint provides general guidance, not legal advice.