How to Get a Plumbing Work Permit in Richmond, VA (2026 Guide)
Everything you need to know about plumbing work permits in Richmond, VA, local requirements, fees, timelines, and how to apply.
By Joey, Founder · Last updated May 23, 2026 · How we research →
Check your specific plumbing work project
Get an instant, personalized answer for your exact project details in Richmond.
Free Permit Lookup →Do You Need a Plumbing Work Permit in Richmond?
Based on Richmond's local building codes, you'll need a permit when:
Adding a new plumbing fixture requires a plumbing permit.
Replacing a water heater requires a plumbing permit.
Re-piping a house requires a plumbing permit.
These plumbing work projects are typically exempt in Richmond:
Replacing a plumbing fixture (faucet, toilet) in the same location does not require a permit.
Permit Fees in Richmond
Based on local Richmond permit data, fees for plumbing work projects typically range:
Here's how fees break down by project scope nationally:
| Project Scope | Typical Permit Fee |
|---|---|
| Water heater replacement | $50 – $200 |
| Single fixture addition or relocation | $75 – $300 |
| Adding a bathroom | $150 – $500 |
| Gas line installation | $75 – $300 |
| Whole-house repipe | $200 – $500+ |
| Sewer line repair/replacement | $150 – $500+ |
Fees are typically calculated based on estimated project value. Contact City of Richmond Department of Planning & Development Review for exact amounts.
How Long Does It Take?
In Richmond, typical approval time for plumbing work permits is about 2 weeks.
More complex projects requiring structural review or variances may take longer. Simple projects may qualify for expedited or over-the-counter review in some cases.
How to Apply for a Plumbing Work Permit in Richmond
- 1 Check requirements: Use our free lookup tool or contact City of Richmond Department of Planning & Development Review to confirm your project needs a permit.
- 2 Gather documents: Prepare your application, site plan, construction drawings, and any other required documents.
- 3 Submit online: Richmond accepts applications online at City of Richmond Department of Planning & Development Review.
- 4 Pay fees: Pay the applicable permit fees ($50 – $600).
- 5 Wait for approval: Your application will be reviewed by Richmond plan reviewers. Typical turnaround is about 2 weeks.
- 6 Begin work: Once approved, post your permit visibly at the job site before starting work.
- 7 Schedule inspections: Call City of Richmond Department of Planning & Development Review at (804) 646-4169 to schedule required inspections at each phase of the project.
Richmond Building Department Contact
Required Inspections in Richmond
Most plumbing work projects in Richmond require inspections at each construction stage:
Rough-In Plumbing Inspection, Pipe sizes and materials correct, drain slope (1/4 inch per foot for pipes under 3 inches), vent routing and distances per IRC Table P3105.1, cleanout placement, pipe support and hangers, firestopping at penetrations. Supply lines pressure-tested at 50 PSI minimum for 15 minutes. DWV system water-tested (filled to 10 feet above highest fitting, held 15 minutes). Gas piping tested at 3 PSI for 10 minutes.
Shower Pan / Liner Test (if applicable), Pan filled with water to the threshold height, held for 15 minutes minimum with no leaking. Liner properly installed and turned up walls. Drain connection sealed.
Final Plumbing Inspection, Every fixture drains properly, all traps filled with water, no leaks at any connections, gas connections leak-tested (if applicable), water heater installation complete and correct (T&P valve, expansion tank, venting, strapping), backflow prevention devices in place, and hose bibb vacuum breakers on all exterior faucets.
Schedule inspections with City of Richmond Department of Planning & Development Review at (804) 646-4169 at least 24–48 hours in advance.
Frequently Asked Questions
Whether you need a permit depends on the size and scope of your plumbing work project. In Richmond, some smaller projects are exempt while larger ones require a permit. Use our free lookup tool to check your specific situation.
Permit fees for plumbing work projects in Richmond typically range from $50 – $600. Fees are usually based on the estimated project value.
Typical approval time in Richmond is about 2 weeks. Complex projects requiring structural review may take longer.
In most cases, homeowners in Richmond can pull permits and perform work on their own primary residence as an owner-builder. You're still responsible for meeting all code requirements and passing inspections.
Working without a required permit in Richmond can result in fines, stop-work orders, required removal of completed work, and complications when selling your home.
Ready to check your plumbing work project in Richmond?
Use our free lookup tool to get a personalized answer based on your specific project details.
Free Permit Lookup →Other Permit Guides for Richmond, VA
Explore more permit guides for Richmond:
Plumbing Work Permits in Nearby Cities
See plumbing work permit requirements in other Virginia cities:
See Detailed Plumbing Work Rules for Richmond
View all local rules, exemptions, and fee details on the permit page.
Plumbing Work Permit Rules →